Долговечность роторных ножей для суперконцентратов (Masterbatch) в высоконаполненных компаундах
High‑filler masterbatch (glass fiber, CaCO3, talc, TiO2) is unforgiving on rotary cutters. Hard particulates plough the edge, accelerate rounding and micro‑chipping, and magnify any error in clearance, run‑out, or parallelism. The result is rising fines, tails, and unstable pellet geometry that drags down throughput and downstream yield. This guide focuses on extending life, reducing fines/tails, […]
Регулировка зазора между стационарным ножом и ротором для идеального чистого среза
Introduction A crisp, square pellet depends on one thing more than any other: how precisely you set the bed knife–to–rotor gap. Get this right and you’ll stabilize pellet shape, suppress fines, and stretch the time between interventions. Miss it and you’ll fight tails, dust, and unplanned stops. Strand pelletizers run in a near‑zero clearance regime—sharp […]
Услуги прецизионной заточки роторных фрез и стационарных ножей
Inspecting a rotary cutter and bed knife with micrometer and optical scope to verify geometry before reinstallation. Pellet quality, uptime, and total cost per ton all hinge on one deceptively simple thing: edge accuracy. When the cutting edges on the rotary cutter and bed knife drift from target geometry, pellets show tails and fines, vibration […]
Роторная фреза для прецизионных систем Scheer: качество выше, цена ниже OEM
If you run Scheer strand pelletizers in the S3500/SGS families, you’re measured on pellet quality, runtime, and cost per ton. This guide shows exactly how to select, install, and validate high-precision replacement rotors and knives—so you can protect pellet geometry, cut fines, and reduce OEM spend without risking compatibility. What you’ll get here: a practical […]
Динамическая балансировка роторных фрез для устранения вибрации
High-speed vibration robs you of uptime and quality. On rotary cutters, even a few tenths of a gram out of place can turn into jarring forces at operating RPM, showing up as chatter marks, tails and fines, premature knife wear, bearing heat, and rising scrap. Static balance helps with heavy spots in one plane, but […]
Роторные фрезы с твердосплавными вставками увеличивают время безотказной работы при переработке стеклопластика (GFRP)
By Tommy Tang (Senior Sales Engineer, Nanjing METAL Industrial). 12 years in slitting & industrial cutting applications. Certifications: CSE, CME, Six Sigma Green Belt, PMP. Introduction Glass fiber–reinforced polymers (GFRP) are unforgiving on cutting edges. Hard, silica-based fibers abrade the knife, rounding the edge and seeding micro‑chips that show up as tails and later break […]
Руководство по винтовым роторным фрезам для бесшумной высокоскоростной резки
In strand pelletizing, polymer strands are guided into a rotary cutter that shears them against a fixed bed knife to create consistent pellets. A helical rotary cutter uses spiral knives rather than straight edges, so the cut occurs progressively along a helix instead of across the full width at once. At high RPM, this progressive […]
Ножи для роторного гранулятора стандарта OEM — Роторные ножи для систем Gala, MAAG и Scheer
If you’re responsible for equipment, process, or purchasing on a strand pelletizer (MAAG Automatik/Scheer) or you maintain underwater systems (Gala/MAAG) as a secondary line, this guide is for you. OEM‑equivalent fit is what protects uptime and pellet quality: the moment OD/ID, thickness, bolt circle, or bore/pin fits drift, you get tails, rising fines, and more […]
Роторные ножи для гранулятора пластика для GF‑PA66: от конструкции до производительности
GF‑PA66 loads a cutting edge the way sand loads a pump: glass fibers abrade, heat accelerates softening at the land, and any loss of geometry shows up immediately as fines, tails, or unstable pellet length. That is why rotor plastic pelletizer blades working on glass‑filled nylon demand higher wear resistance, tougher micro‑edges, and tighter control […]
Ножи роторного гранулятора с твердосплавными вставками для долгой службы
If you run underwater pelletizing on PP or PE, you feel blade life in your uptime, pellet geometry, and cost per ton. When blades hold a clean edge longer, you swap less, stabilize pellet length and roundness, and trim changeover hours. Failures usually start in a few familiar places: steady abrasion from fillers and pigments, […]
English 
Spanish 
Italian 
French 
Portuguese 
Russian 
German 
Arabic 
Hindi 
Vietnamese 
Indonesian 
Japanese 
Korean